It is a continuous decorative covering with a thickness of 2-3mm, with a cement base combined with an extensive formulation of additives, aggregates, polymers and fibres.

CEMENTEC allows you to achieve results with high creative value and amazing finishes, thanks to its capacity for customisation provided by its different products, and its wide range of colours and textures.

One of the main advantages of microcement is that it can be applied on almost all types of surfaces, such as cement-based surfaces, self-levelling mortars, ceramic, terrazzo, marble, paving stones and all types of correctly anchored tiles.

Furthermore, for walls, the best surface for application is plasterboard or screed plaster.

Another advantage of microcement is avoiding the debris generated by the existing covering, facilitating and speeding up refurbishments, for example, in bathrooms, toilets or kitchens.

The smoother, better anchored and stronger the surface to be covered is, the less previous adaptation we will have to carry out.

Practically no previous adaptation is required when the microcement is directly applied on plasterboard walls or perfectly cast screed plaster. Other rest of surfaces always require previous adaptation.

Cementec offers a range of video tutorials with exhaustive adaptation of surfaces, necessary to avoid any type of future problems.

This previous adaptation is carried out using specific products for proper preparation. For example, in the case of surfaces with joins, a previous adaptation with resins, fiberglass meshes and other products has to be carried out to block the appearance of the join in the covering applied.

Parquet or natural wood floors are not rigid enough, and also have a type of elasticity that can cause some issues in microcement such as fissures or cracks. In these cases, it is necessary to take out the existing floor, and assess its suitability for applying the microcement.

Microcement is perfect for application in wet areas such as sinks, bathtubs, shower trays, etc.

CEMENTEC® has specific products to be used in wet areas. Furthermore, with the Finish Forte Plus protection system, we provide all the necessary waterproofing to be used as normal, being a unique protector which is currently unparalleled.

Microcement and underfloor heating are fully compatible. In fact, we would say that microcement is one of the most recommended coverings to be used in this type of flooring, due to both its great thermal conductivity and the comfort it provides.

Of course, a small protocol for turning on heating must be carried out prior to application, to avoid possible cracks caused by temperature changes.

Microcement is a product with high flexural strength, which increases its ability to prevent fissures or cracks.

However, we cannot know precisely what the behaviour of the original base against movements or settlements of the building may be; therefore, we strongly recommend the use of fiberglass mesh on surfaces with joins or cementitious surfaces.

In addition, at Cementec we have two types of mesh, 150g/m2 and 80g/m2, depending on the original surface.

This is another of the main advantages of microcement; it requires practically no maintenance.

As long as the varnish is in good condition, no special maintenance is required. In addition, it can be cleaned with any type of product.

In the long term, after a few years and depending on use, protective varnishes can be reapplied with a minimal cost.

Expansion joints do not have to be carried out during the application of microcement.

Only in cases where the existing surface contains that type of join, then they must be respected.

However, this will not necessarily be noticeable, as our system allows you to minimise its thickness to make it barely noticeable.

Expansion joints do not have to be carried out during the application of microcement.

Only in cases where the existing surface contains that type of join, then they must be respected.

However, this will not necessarily be noticeable, as our system allows you to minimise its thickness to make it barely noticeable.

Within the variety and range of products that we have, we can offer you our impressive Cementec High Transit.

It’s a microcement with a high surface resistance, and other values above any standard type of traditional microcement.

Recommended for rooms or public areas where foot traffic is much denser or with more intense use. If you are looking for a covering with high hardness and resistance, Cementec High Transit is the best choice.

There are some differences in this regard.

First of all, the thickness of application, as concrete requires thicknesses greater than 2cm, and microcement approximately 2-3mm.

The thickness of concrete can easily cause the appearance of cracks. Second, viability: microcement can be applied in many areas where concrete is totally unfeasible.

Finally, the aesthetics, as microcement is much more decorative than in concrete.

We currently have a wide range of colours with about 16 different shades.

In addition, we have the new Vintage range, with 5 shades where an aged and textured style of microcement is offered.

Finally, there is the metallic range with 6 different colours for applications where a different and unique touch is sought.

In case of needing a different colour from our range, we can customise a different one for applications over 250m2.